Test & Measurement Instruments

Approx. Rs 8,500 / PieceGet Latest Price

• It is a transducer which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms.
• Its current transducer is composeof permalloy and hall element, which linearly transform the AC or DC current to AC or DC current voltage. And if connecting to an oscilloscope by BNC type connector, you''re able to observe the current waveforms; If connect to a multimeter by banana type connector, you can obtain the current data.

• Power circuit measurement and malfunction analysis;
• Motor drive of frequency converter (or other electronics) measurement;
• Power electronics equipments measurement.

Approx. Rs 46,000 / PieceGet Latest Price

• Two-channel USB digital oscilloscope (1MΩ, ±25V, differential, 14-bit, 100MS/s, 30MHz+ bandwidth - with the Analog Discovery BNC Adapter Board)
• Two-channel arbitrary function generator (±5V, 14-bit, 100MS/s, 12MHz+ bandwidth - with the Analog Discovery BNC Adapter Board)
• Stereo audio amplifier to drive external headphones or speakers with replicated AWG signals
• 16-channel digital logic analyzer (3.3V CMOS and 1.8V or 5V tolerant, 100MS/s)
  • Digital Bus Analyzers (SPI, I²C, UART, Parallel)
• 16-channel pattern generator (3.3V CMOS, 100MS/s)
  
• 16-channel virtual digital I/O including buttons, switches, and LEDs – perfect for logic training applications
• Two input/output digital trigger signals for linking multiple instruments (3.3V CMOS)
• Single channel voltmeter (AC, DC, ±25V)
• Network Analyzer – Bode, Nyquist, Nichols transfer diagrams of a circuit. Range: 1Hz to 10MHz
• Spectrum Analyzer – power spectrum and spectral measurements (noise floor, SFDR, SNR, THD, etc.)
• Data Logger - Exportable data and plot functionality
• Impedance Analyzer - Capacitive and Inductive Elements 
• Protocol Analyzer - SPI, I2C, UART, and CAN
• Two programmable power supplies (0…+5V , 0…-5V). The maximum available output current and power depend on the Analog Discovery 2 powering choice:
  • 500mW total when powered through USB. (Each supply can provide between 0mW and 500mW so long as the total does not exceed 500mW.)
  • 2.1W max for each supply when powered by an auxiliary supply.
  • 700mA maximum current for each supply.
• An available Software Development Kit for programming with Python and C++, and a toolkit for programming with LabVIEW.
• MATLAB support for the Data Acquisition Toolbox

Additional Information:

• Minimum Order Quantity: 1 Piece

Approx. Rs 7,500 / UnitGet Latest Price

Approx. Rs 65,900 / PieceGet Latest Price

Approx. Rs 11,500 / PieceGet Latest Price

• Embedded Processing
• Processor Boards
• Basys MX3 PIC32MX Trainer Board: Recommended for Embedded Systems Courses
• Basys MX3 PIC32MX Trainer Board: Recommended for Embedded Systems Courses $99.00SKU:410-336Quantity: ShareProduct Description

• Processor/IC: Microchip PIC32MX370F512L Microcontroller
• MIPS32® M4K® core runs up to 96 MHz using onboard 8 MHz oscillator
• 512 KB of Program Flash Memory
• 12KB of Boot Flash Memory
• Four Direct Memory Access (DMA) Modules
• Two SPI, Two I²C, and Five UART serial interfaces
• Parallel Master Port (PMP) for graphics interfaces
• Five 16-bit Timers/Counters
• Five Input Capture Modules
• Five Output Compare Modules
• 85 I/O pins
• 54 pins support Peripheral Pin Select (PPS) for function remapping
• Software
• Designed for use with MPLAB X IDE
• System Features
• 4 MB SPI Flash
• Onboard USB UART (USB Micro cable required, NOT INCLUDED)
• Supports baud rates up to 1.25 MBaud
• Powered from USB or 5 V external power source
• Standard barrel jack for 2.0 mm internal-diameter plug
• No jumper select required
• System Connectivity
• USB-UART Bridge
• Interaction and Sensory Devices
• 8 Slide Switches
• 5 Buttons
• 1 Reset Button
• 8 LEDs
• 1 RGB LED
• Onboard 3-axis, 12-bit accelerometer
• Programmable Motion Detection
• I2C Interface with Programmable Interrupt
• Onboard FIR-compatible IrDA Module
• Built-in Remote Control Transmission Function
• Supports speeds up to 4 Mbps
• Onboard Audio Input and Output
• MEMS Microphone with Adjustable Gain
• Thumbwheel potentiometer for adjusting mic volume
• PWM driven mono audio output with onboard speaker
• Thumbwheel potentiometer for adjusting speaker volume
• 3.5 mm jack for line out connection to external amplifier/speaker system
• Onboard Displays
• 2x16 LCD Character Display with LED backlight
• 4-Digit Seven Segment Display with red LEDs
• Motor Control
• Onboard Dual H-Bridge Motor Driver
• Supports up to two 1.5 A Brushed DC Motors or one stepper motor
• Supports motor voltages up to 11 V
• Terminal block provides easy connection to motors
• 2 Servo Connectors
• Analog Input Control (AIC)
• Thumbwheel potentiometer for varying analog input between 0 to 3.3 V
• Two wire loops for ground and AIC
• Expansion Connectors
• Two 2×6 Pmod host ports
• SPI, UART, GPIO, PWM, analog in
• Terminal block for two DC motors or one stepper motor
• Two R/C servo connectors
• One I²C connector
• Debugging
• Onboard 30-pin Analog Discovery 2 connector
• Onboard USB programmer/debugger
• Program/debug the PIC32MX370 directly from MPLAB / MPLAB

Approx. Rs 12,100 / PieceGet Latest Price

• Cost effective, PC USB Function/Arbitrary Waveform Generator.
• It can be used to disengage computer. Simulation of sensors and real word signals.
• It can be used as the other products signal generator module, no need computer. It will produce the needed arbitrary waveform signal when power on.
• 200 MS/s of sample rate, 12 bits of vertical resolution.
• 25Mz Arbitrary waveform output (sine wave up to 75 Mz).
• One computer can be linked with several DDS-3X25 to expand multi-channels.
• 50 MHz frequency counter.
• 12bits pattern generator.
• USB interface, plug, and play, no need external power supply, compact and portable.
• Operating system: Windows NT, Windows 2000, Windows XP, Windows Vista, Windows 7.
• Second Design support: Labview\VB\VC\Delphi\C++Build. Provide second design examples.